ADJUSTABLE VICTORIAN GABLES
- ALL STYLES ARE COMPLETELY ADJUSTABLE - NO ROOF PITCH MEASUREMENTS NECESSARY -
NOTE: - One of the problems homeowners face in putting up a gable is the determination of the correct fit. The below example videos and pictures will illustrate how easy our gables can be sized and installed. Taking all the guesswork out of pitch and degree of angle. The gable sets are designed to be nailed flat onto your existing fascia boards, or with a little more work, hang from the bottom of your fascia boards. See videos below for demonstration.
I make gable sets in a variety of sizes allowing a good fit to any roof line or window decoration. They can be installed touching or spread apart to still give a gable look. This selection of sizes will allow you to use them on various places on your house so they all tie in. If you are looking for a porch bracket to tie into this design, I have several - see -STANDARD BRACKET PAGE -
As gables are installed exposed into the full sun and weather I construct each piece from high grade external manufactured wood designed exactly for this type of use. Rot, bug and water resistant. This is a strong manufactured wood designed for outside exterior applications. All gables are shipped primed white and sanded to accept paint. In this application I always strongly suggest two coats of good external latex house paint. Please call with any questions OR TO ORDER GABLES. - All Victorian Gable Sets are shipped sealed and primed.....ready to paint.
- INFORMATIONAL VIDEO ON OUR ADJUSTABLE VICTORIAN GABLES -
The Royal Gable Set
Available in six sizes - can be installed in either direction
Item # Royal 17 $79.00 set
EACH PIECE MEASURES: 17 5/8 inches long by approx 7 3/4 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
Item # Royal 32 $149.00 set
EACH PIECE MEASURES: 32 1/2 inches long by approx 14 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
Item # Royal 22 $89.00 set
EACH PIECE MEASURES: 22 3/4 inches long by approx 9 3/4 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
Item # Royal 36 $189.00 set
EACH PIECE MEASURES: 36 inches long by approx 15 1/2 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
Item # Royal 27 $109.00 set
EACH PIECE MEASURES: 27 1/2 inches long by approx 11 3/4 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
Item # Royal 42 $239.00 set
EACH PIECE MEASURES: 42 inches long by approx 18 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
SUPPORT BAR OPTION
NOTE: For those wishing to hang this gable rather than nail flat against a fascia board, I can make custom fitted support frames. Just mention during ordering. I construct the support bars here in the shop and bevel the edges, then counter sink mounting holes top and bottom and ready for your exterior screws. After I attach the gable to the support strip with glue and nails, I caulk around the seam. The support bar will add approximately two inches top and bottom to overall gable section length. The entire unit is then primed and ready for you to paint.
The Coventry Gable Set
Available in six sizes - can be installed in either direction
Available with or without pre attached support bars.
This adjustable Gable style lends itself very nicely for either nailing flat against your existing fascia boards or, hanging down from the Fascia board. I offer this design in both varieties and can attach an optional support bar. NOTE: support bars add approximately 2 inches to each end.
Item # Coventry 21 $89.00 set
EACH PIECE MEASURES: 21 1/2 inches long by approx 7 1/2 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
Item # Coventry 36 $179.00 set
EACH PIECE MEASURES: 36 inches long by approx 13 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
Item # Coventry 26 $109.00 set
EACH PIECE MEASURES: 26 1/2 inches long by approx 9 1/4 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
Item # Coventry 42 $219.00 set
EACH PIECE MEASURES: 42 inches long by approx 15 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
Item # Coventry 31 $139.00 set
EACH PIECE MEASURES: 31 3/8 inches long by approx 10 3/4 inches wide at widest point
- SET OF 2 PIECES TO FORM ONE GABLE -
Set of support bars add $20.00
THE BRISTOL
This adjustable gable system is available in two sizes and included with our standard type gable sets for installation that are tight spots. It is similar to our popular Coventry system above, but narrower.
AVAILABLE SIZES: set of two pieces to form one Gable set - One inch thick manufactured wood.
Item # Bristol 25 - 25 1/4 long by 6 3/4 wide at the top. $99.00 ea set.
Item # Bristol 36 - 36 1/2 inches long and 10 inches wide at the top. $169. ea set.
Support bar option - $20.00 per set
THE DOVER
This adjustable Gable style lends itself very nicely for either nailing flat against your existing fascia boards or, hanging down from the Fascia board. I offer this design in both varieties and can attach an optional support bar.
NOTE: support bars add approximately 2 inches to each end. Please call to order this design.
AVAILABLE SIZES: set of two pieces to form one Gable set - One inch thick manufactured wood.
Item # Dover 27 - 27 inches long by approx 10 inches wide at widest point $ 159.00 set - SET OF 2 PIECES TO FORM ONE GABLE
Item # Dover 36 - 36 inches long by approx 12 1/2 Inches wide at widest point $189.00 set - SET OF 2 PIECES TO FORM ONE GABLE
Item # Dover 42 - 42 inches long by approx 15 inches wide at widest point - $229.00 set. SET OF 2 PIECES TO FORM ONE GABLE
Support bar option - $20.00 per set
DROP FINIAL
Yes I have a drop finial available. 1 1/2 inch thick with a turned end. 30 inches long to allow you room to make a custom cut for your individual application. Carved birch finial inserted into a solid Western Red Cedar post.
Item # Drop Finial - $23.95 ea.
Yes we make a Victorian ROOF trim to compliment our gable designs in width from 3-6 inches.
VICTORIAN ROOF TRIM
All content (c) Victorian Design Woodshop - All rights Reserved - ABOUT